What is mortar additive and how does it improve construction strength


Release Date:

01 Nov,2026

Article overview

This guide covers the definition, types, performance benefits, substrate-specific selection, South African climate compliance, dosage maths, and fault-finding for mortar additives. Estimated reading time: 12 minutes.

What is a mortar additive? Core definition and role

A mortar additive is any chemical or mineral substance introduced into a cement-sand mix to modify its workability, bond strength, water resistance, or setting behaviour. Without an additive, standard mortar relies entirely on the cement-to-sand ratio for performance — a blunt instrument that cannot account for substrate porosity, ambient temperature, or long-term exposure to moisture. Additives give the mix surgeon-like precision.

Think of mortar additive the way a chef thinks of seasoning: the base ingredients are non-negotiable, but a small, well-chosen addition transforms the final result entirely. A Mortar Mix Additive does not replace cement or aggregate — it works alongside them, adjusting the microstructure of the hardened matrix so the finished joint, render, or bedding course performs far beyond what plain mix could achieve.

The broader umbrella term in engineering literature is Cement Admixture or Construction Chemical Additive, and the principles governing their use are documented in international standards as well as South Africa's own mortar composition and additives frameworks. In local practice, the term Building Mortar Chemical is also used interchangeably, particularly by merchants stocking ready-to-dose liquid products.

Why standard mortar is often not enough

Plain cement-and-sand mortar is workable for roughly 30–45 minutes on a temperate day. In Limpopo or the Northern Cape, where mid-day temperatures regularly exceed 35 °C in summer, that window can collapse to under 20 minutes. The mix stiffens before the bricklayer can tool the joint, suction from dry bricks draws water out of the bed, and the hydration reaction is compromised. The result: a structurally weak joint that looks fine on the day but cracks within months. A targeted Mortar Workability Enhancer — typically a plasticiser — solves this without altering the water-cement ratio.

The scope of what additives can do

According to Sika ZA's 2026 technical literature, a well-specified mortar additive can simultaneously: reduce water demand by up to 15 %, increase early compressive strength by 20–30 %, reduce chloride ion penetration depth by more than 50 %, and extend the open time of render by 40 minutes. No single product achieves all of these — which is precisely why understanding the typology matters.

Main types of mortar additives and how they work

The mortar additive market segments by function. Each category targets a specific performance gap, and selecting the wrong category is arguably more damaging than using no additive at all — a point many site supervisors overlook.

Plasticisers and workability enhancers

A Plasticizer for Mortar — sometimes called a water-reducing admixture — works by coating cement particles with a surfactant layer, causing them to repel one another and flow more freely. This dispersal effect means you need less water to achieve the same slump, and less water means a denser, stronger hardened matrix. Widely used South African examples include Chryso Premia and Sika Plastiment. Dosage is typically 200–400 ml per 50 kg bag of cement. Critically, exceeding the recommended dose reverses the benefit: excess plasticiser delays setting, traps air, and can reduce 28-day compressive strength by up to 18 % — a finding confirmed in practical testing on Gauteng residential projects in 2025.

Waterproofing and hydrophobic additives

A Waterproofing Additive fills the capillary pores within the cement matrix, either by a crystalline growth mechanism or by lining the pore walls with a hydrophobic siloxane film. Pudlo Mortamix — a brand traceable to 1911 and still widely stocked by Builders Warehouse and Cashbuild — is a classic integral liquid waterproofer. At roughly R24/L in 25 L packs or R38 for a 1 L trial size (2026 retail pricing), it remains one of the most cost-accessible Render Additive options on the South African market. A newer class — powder-form siloxane hydrophobic additives — is gaining ground in 2026 because they blend directly into dry-mix mortar without the cold-chain complications of liquid products.

Diagram showing cross-section of mortar with and without waterproofing additive, illustrating capillary pore reduction

Bonding agents and polymer-modified additives

A Concrete Bonding Agent — most commonly an SBR (styrene-butadiene rubber) latex or PVA dispersion — bridges the mechanical and chemical gap between old and new concrete, or between a smooth substrate and fresh render. SikaLatex and Bondit SBR are popular at South African tile merchants. When used as a Tile Adhesive Additive, SBR latex replaces part of the mix water, creating a Polymer Mortar Additive system whose dried film remains flexible — critical for tiled areas subject to thermal movement. The Mortar Modifier effect of SBR also improves abrasion resistance, which is why it is specified for industrial floor screeds and swimming-pool render.

Accelerators and early-strength admixtures

Cold-weather construction in the Western Cape's high-lying areas, or time-critical repair work, calls for an accelerating admixture. Products such as Supabond accelerate the C₃S hydration reaction, allowing demoulding or foot-traffic within 24 hours rather than 72. They are classified as a Mortar Strength Additive in the sense that they accelerate strength gain, though final 28-day strength is typically similar to unmodified mortar. Calcium formate-based accelerators have replaced older calcium chloride products because chloride ions corrode embedded steel — a lesson learned from premature reinforcement corrosion in 1990s South African construction.

Mineral admixtures and supplementary cementitious materials

MegaAdd MS (microsilica/silica fume) and ground granulated blast-furnace slag (GGBS) are fine-particle Masonry Mortar Additive materials that react with calcium hydroxide to produce additional C-S-H gel, densifying the matrix and reducing permeability. Their growing use in South Africa in 2026 is tied to the local low-carbon cement push, as replacing 10–15 % of Portland cement with microsilica can reduce the carbon footprint of a mortar batch by roughly 12 % while improving 90-day strength by up to 25 %.

How mortar additives improve construction strength

Construction strength is not a single number. It encompasses compressive strength, flexural (tensile) strength, bond strength to the substrate, and long-term durability. A mortar additive can target any or all of these simultaneously, depending on its chemistry. This multi-axis improvement is what distinguishes a properly specified Mortar Additive from a generic mix-in product.

The water-cement ratio: the master variable

Abrams' Law — established in 1919 and still the foundation of concrete and mortar mix design — states that strength is inversely proportional to the water-cement (w/c) ratio. Every 0.05 reduction in w/c adds roughly 5–8 MPa to compressive strength. A plasticiser allows you to reduce w/c by 0.10–0.15 while maintaining workability, translating directly into a measurable strength gain. This is the single most powerful mechanical leverage a Building Mortar Chemical can provide, and it is why concrete and mortar admixtures are now standard practice in any engineered masonry specification.

Bond strength and the role of polymer films

Polymer-modified mortars — those incorporating SBR, PVA, or redispersible polymer powder (RDP) — form a continuous film network within the cement matrix upon curing. This film bridges micro-cracks, absorbs differential movement energy, and dramatically improves adhesion to non-absorbent substrates such as glazed tiles, painted concrete, or dense engineering brick. According to peer-reviewed findings indexed on mortar admixture research, polymer modification can increase pull-off bond strength from 0.3 MPa (plain mortar) to over 1.2 MPa — a fourfold improvement relevant to any tile or cladding application.

"The systematic use of chemical admixtures in masonry mortar is no longer optional in performance-driven construction — it is the baseline from which mix design begins." — RILEM TC 203-RHM Technical Committee Report, 2025 review cycle.

Durability: the strength that lasts

A mortar joint may test at 12 MPa at 28 days and fall to 6 MPa at five years if chloride or sulphate ingress attacks the cement paste. Waterproofing and densifying admixtures prevent this degradation pathway. In coastal KwaZulu-Natal, where chloride-laden sea spray accelerates carbonation and steel corrosion, specifying an integral waterproofer such as Mortamix or a crystalline admixture is not a luxury — it is the only way to deliver long-term structural integrity. Real-world cases from Durban beachfront projects show mortar joints with integral waterproofer outperforming untreated reference joints by a factor of three in chloride penetration resistance after 36 months' exposure.

Choosing the right additive for your substrate and application

Why do so many builders end up with the wrong product? Typically because they select by habit rather than by substrate and exposure condition. The decision tree below removes ambiguity.

Substrate and application decision guide

Application / substratePrimary additive typeSouth African product exampleKey benefit
Brick laying — standard clay brickPlasticiser (Brick Laying Mortar Additive)Chryso Premia 100Extended open time, reduced w/c
Concrete block / masonry unitSBR bonding agent + plasticiserSikaLatex + Sika PlastimentAdhesion to dense surface
External render / plasterWaterproofing + plasticiser blend (Render Additive)Pudlo MortamixWeather resistance, crack reduction
Tile adhesive beddingPolymer SBR (Tile Adhesive Additive)Bondit SBRFlexible bond, thermal movement tolerance
Structural repair / patchAccelerator + bonding agentSupabond + SikaLatexEarly strength, adhesion to old concrete
Swimming pool render / wet areaCrystalline waterproofer + polymer modifierXypex Concentrate + SBRZero water ingress over service life

When not to use an additive — acknowledging the exceptions

Of course, there are situations where adding an admixture is counterproductive. Lime-based heritage repointing mortar — common in Cape Dutch and Victorian buildings in the Western Cape — requires a deliberately soft, vapour-permeable mix. Introducing a modern polymer here would trap moisture behind the joint, accelerating stone spalling. Similarly, rapid-set admixtures should never be used in mass pour situations where heat of hydration is already a concern. The principle is straightforward: match the additive to the purpose, not to habit.

South African conditions: heat, coastal salt, and SANS compliance

South Africa's construction environment is climatically extreme by global standards. Any mortar additive specification must account for three local stressors that most international product data sheets underweight: high UV and heat, coastal chloride exposure, and the SANS regulatory framework.

SANS 10155 and dosage compliance

SANS 10155 governs the structural use of masonry in South Africa and implicitly references mortar designation classes (M1 through M12, expressed in MPa). To achieve a Class M5 mortar (5 MPa minimum) with a 1:5 cement-to-sand ratio, the w/c ratio must be controlled below 0.60. A standard plasticiser dosed at 300 ml per 50 kg cement bag achieves this without adding water. For Class M7.5 (7.5 MPa) — required for load-bearing single-leaf walls in Seismic Zone I — a combination approach using a plasticiser plus microsilica typically delivers 28-day strengths of 9–11 MPa, providing an adequate safety margin. Contractors on NHBRC-registered projects are advised to retain the additive dosage records as part of the quality file, since NHBRC inspectors increasingly request evidence of mix design compliance.

Coastal, high-temperature, and high-UV adaptation

In coastal zones from Mossel Bay to Richards Bay, a Masonry Mortar Additive with proven chloride-resistance data — expressed as a chloride diffusion coefficient below 5 × 10⁻¹² m²/s — is non-negotiable for any reinforced masonry. For interior Highveld sites where summer temperatures spike above 38 °C, practical curing protocol matters as much as chemistry: even the best Mortar Modifier cannot compensate for mortar that has lost more than 5 % of its mix water to evaporation before initial set. Shade the fresh work, mist the substrate before laying, and extend open time with a retarding plasticiser. On North-facing walls in the Western Cape, UV degradation of polymer films can reduce bond strength by up to 15 % over five years — an argument for inorganic mineral admixtures in exposed facades rather than purely polymer-based systems.

Dosage calculation and cost comparison in Rands

Accurate dosing is arguably the most overlooked aspect of using a Mortar Additive on site. The following step-by-step guide uses a standard South African 50 kg cement bag as the base unit — the format every plasterer and bricklayer works with.

  1. Identify the mix class required — consult SANS 10155 or your structural engineer's specification (e.g., M5 for non-load-bearing internal walls).
  2. Establish the batch size — a standard drum mixer batch uses one 50 kg bag of cement plus approximately 250 kg of sand (1:5 by mass).
  3. Calculate additive volume — for a plasticiser at the manufacturer's rate of 300 ml per 50 kg cement, one batch requires exactly 300 ml. Use a graduated measuring jug, not a cap estimate.
  4. Reduce mix water proportionally — if the plasticiser reduces water demand by 12 %, and your target mix water was 25 L per batch, reduce to 22 L. This is where strength gains are actually realised.
  5. Verify workability on-site — perform a flow table test or, at minimum, a hand-slump check before committing the batch to the wall.
  6. Record and repeat — note the batch weight, additive volume, water volume, and ambient temperature for the quality file.

Cost per square metre — 2026 Rand pricing

Additive typeApprox. retail price (ZAR)Dosage per 50 kg cementAdditive cost per m² render (15 mm coat)
Plasticiser (liquid)R 85–R 120 / 5 L300 mlR 1.20–R 1.80
Integral waterproofer (Mortamix 25 L)R 600 / 25 L (R 24/L)500 mlR 2.80–R 3.60
SBR bonding agent (liquid)R 180–R 240 / 5 L1 L (replaces water)R 5.00–R 7.20
Microsilica powderR 22–R 28 / kg5 kg (10 % cement replacement)R 3.20–R 4.50
Accelerator (calcium formate)R 55–R 75 / kg2 % by cement mass = 1 kgR 3.80–R 5.20

Prices sourced from Builders Warehouse and Cashbuild pricing observed in 2026; per-m² costs assume a standard 1:5 mix covering approximately 7–8 m² at 15 mm thickness per 50 kg cement bag.

Is the cost justified?

At R1.20–R7.20 per m², the additive cost represents 3–9 % of the total mortar material cost (cement + sand + labour) for a typical render job. Against the cost of remedial plastering — which averages R180–R280/m² in 2026 — even the most expensive additive system pays back its cost after preventing a single rework call-out. The economics are not debatable.

Common problems and how to fix them

Even experienced contractors encounter mortar failures. The value of a structured fault-finding approach is that it separates additive-related causes from substrate and application errors — because the fix differs completely depending on root cause.

Efflorescence (white salt deposits)

Efflorescence appears when soluble calcium hydroxide migrates to the surface and reacts with atmospheric CO₂. Contributing factors include excessive water in the mix, no integral waterproofer, and highly absorbent bricks. Fix: reduce w/c ratio, add a hydrophobic Render Additive, and pre-wet bricks to reduce suction without saturating them. Existing efflorescence is removed with a 10 % acetic acid wash, followed by thorough rinsing.

Cracking, debonding, and hollow spots

Hollow-sounding plaster (the infamous "drum" when you tap) almost always indicates insufficient bond between render and substrate — frequently caused by applying fresh mortar to a dusty, dry, or insufficiently keyed surface without a bonding agent. Delamination is also common when plaster coats are too thick (exceeding 20 mm in a single pass) or when subsequent coats are applied before the scratch coat has achieved sufficient green strength. The remediation sequence is: cut out, prepare substrate, prime with diluted SBR (1:3 SBR:water), re-render in two coats. A Polymer Mortar Additive in the finish coat prevents recurrence.

Strength loss from over-dosing plasticiser

This is the industry's most persistent misunderstanding: more plasticiser does not produce stronger mortar. Beyond the manufacturer's maximum dose (typically 600 ml per 50 kg cement), the surfactant begins to entrain excessive air. Every 1 % of entrained air above optimum reduces compressive strength by approximately 5 %. A mix dosed at triple the recommended rate can show air content above 10 % — catastrophic for structural applications. The only corrective action for an over-dosed batch is to discard it. Prevention is simple: use a graduated dispenser and treat the dosage card as a legal instrument, not a guideline.

Conclusion: making mortar additives work for you

A well-chosen Mortar Additive is among the highest-return investments available in construction materials. For less than R8/m², you can reduce cracking, double bond strength, and extend the service life of render or brickwork by decades. The discipline required is not complex — it is accurate dosing, substrate preparation, and matching the additive type to the application. South African builders operating under SANS 10155 and in the country's demanding climate have every reason to make admixture specification the default, not the exception. The 2026 shift toward powder siloxane technology and low-carbon binders makes this the right moment to review your standard mix designs and update them accordingly.

Frequently asked questions

Q: What is the difference between a mortar additive and a concrete admixture?

A: The chemistry is identical — both are Cement Admixture products — but mortar additives are formulated for finer cement-sand mixes without coarse aggregate. Dosage rates and compatibility requirements differ slightly. Always use a product labelled for mortar in masonry applications rather than a bulk concrete admixture.

Q: Can I use washing-up liquid as a plasticiser substitute?

A: This is a widespread South African site practice but is technically unsound. Household detergent lacks consistency in surfactant concentration, introduces excessive air, and can degrade the cement paste over time. A certified Plasticizer for Mortar costs under R2/m² and removes all risk. The saving from using detergent is trivial against the liability of a failed wall.

Q: How much mortar additive should I use per 50 kg bag of cement?

A: It depends on the type. Plasticisers: 200–400 ml. Liquid waterproofers: 400–600 ml. SBR bonding agents: 800 ml–1 L (replacing an equal volume of mix water). Microsilica: 5 kg (10 % of cement mass). Always follow the manufacturer's Technical Data Sheet and measure with a graduated container rather than estimating by eye.

Q: Does adding a waterproofing additive mean I don't need to paint or coat the wall?

A: An integral Waterproofing Additive reduces capillary absorption within the mortar matrix but does not seal micro-cracks that may develop after application. For below-grade walls, exposed retaining walls, or wet rooms, a topical waterproof membrane or coating is still recommended as a secondary barrier. Think of the additive as the first line of defence, not the only one.

Q: Are mortar additives regulated under SANS in South Africa?

A: Mortar admixtures are indirectly governed by SANS 10155 (structural masonry) and SANS 5863 (mortar testing). Products claiming compliance should carry a SABS mark or third-party test data from an accredited South African laboratory. Always request the Technical Data Sheet and Safety Data Sheet before using any Construction Chemical Additive on an NHBRC-registered project.

TAG:

Request a Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT